Rea!

220v 2,2kw Vattenkyld ATC Spindel

Det ursprungliga priset var: 23250kr.Det nuvarande priset är: 18740kr.

leasing
447kr/mån
Info Läs mer om leasing.
Wasa Kredit AB
Betala från 378 kronor i månaden
Totalbelopp 18 740 kr
Uppläggningsavgift 550 kr
Avtalstid Månadsavgift Restvärde
36 mån 562 kr 1 874 kr
48 mån 447 kr 1 874 kr
60 mån 378 kr 1 874 kr
Samtliga belopp är exkl. moms
Företagsleasing via Wasa Kredit
– den smarta finansieringslösningen
Wasa Kredit äger varorna under leasingperioden, ert företag har nyttjanderätt. Månadsavgiften är avdragsgill. I slutet av avtalstiden köper du loss varorna för restvärdet. Företagsleasing erbjuds för köp från 2 400 till 2 000 000 kronor.
Så här gör du:
Varukorg Lägg varorna i varukorgen och gå till kassan.
Avtalstid Välj mellan avtalstiderna 36, 48 eller 60 månader.
Kort Avtalsprocessen är automatiserad och kreditkontroll görs direkt i kassan.
Mobil Slutför beställningen med signering av BankID av bolagets firmatecknare.
Avtal När avtalet godkänts kan varorna levereras.

Slut i lager

Vi har tyvärr slut på denna produkt men du finner liknande här: 220v 2,2kw Vattenkyld ATC Spindel

Artikelnr: YV16632 Kategori:

Product Description

Vi har tyvärr slut på denna produkt men du finner liknande här: 220v 2,2kw Vattenkyld ATC Spindel

ATC spindel för automatiskt byte av skär. Observera att vi inte har någon support alls på denna produkt, utan det är upp till dig om du klarar av att installera den. Om du redan har en 2.2kw spindel så kan du använda samma inverter för att köra denna spindel.

Om du behöver verktygshållare till denna spindel (ISO 20) så finns det på hemsidan som produkt, se ”ISO20 ER16 Collet Chuck 40,000RPM”

Beskrivning av spindel sker på engelska och direkt från tillverkaren

Spindle Model:GDL80-20-24Z/2.2
Voltage: 220v
Power: 2.2kw
Current: 7.6A
Frequency: 800Hz
Rotating speed: 24000rpm/30000rpm
Pole number: 4P
Phase number: 3
Weight(kg):8KG
Blind rivet: IS020-15°
Tool holder: IS020
Rotating direction: Rotate anticlockwise from the shaft extension end

1.The electric main shaft shall be installed at the clamped position; otherwise the bearing will be easily damaged!

2. The main shaft shall entirely stop before the tool changing. The manual tool changing button shall not act during the rotation of the shaft; otherwise it will easily result in the seizure of the shaft!

3. The compressed air shall be clean and dry, and the filter accuracy shall be 0.1 micron! Air seal is normally open. It is recommended to use the two-level filter, and the filter accuracy is 0.5 micron/0.1 micron respectively. The air filter is installed with the self-discharge device.

1: Power line Three-color lines connected with U.V.W phases/yellow and green wires grounded. Temperature controlline 110℃ therminstor two- phase connected with the temperature-control protector.

2: Cooling water feed Pump lift 8m

3: Pole change and dust removal pressure 0.2-0, 3Mpa (6/4 hoses)

4: Quantity of proximity switchesPole hanging and pole discharge NPN (normally open) N.O. Wiring method of the proximity switch Brown wire connected with +24VDC/the other end connected with the balck wire.

5: Air seal pressure 0.1-0.2Mpa (4/2 hoses)

6: Cooling water yielding (2 and 6 ends terminated with 8/6 hoses)

7: Air inlet pressure of the cylinder 0.65Mpa (6/4 hoses)

1. Our Ceramic ball bearings spindle use 4 pcs ceramic ball bearings.

2. Ceramic ball bearings are resistant to high temperatures and low heat , usually 3-5 degrees lower than steel ball bearings during using .

3. Ceramic ball bearings have low friction, low noise and long service life.

4. If you want to use the spindle for aluminum, hard wood, then ceramic ball bearings better than steel ball bearings.

Because this product has the characteristics of compact structure, light weight, small inertia and low vibration, it can realize high-speed, high-precision and high-running-stability milling processing.